126 lines
4.4 KiB
Markdown
126 lines
4.4 KiB
Markdown
# NixOS on Pinecube (Early work in progress)
|
|
|
|
Build an SD card image with `./build.sh`.
|
|
Prebuilt image [here](https://drive.google.com/file/d/1A3dreaxXnRpC_tdUey9V5ojnUXhLjLFd/view?usp=sharing) (last updated 2020-11-07).
|
|
Decompress and flash with:
|
|
```shell
|
|
$ cat ./result/sd-image/nixos-sd-image-21.03pre-git-armv7l-linux.img.zst | zstd -d | dd of=/dev/sdX bs=1024
|
|
```
|
|
|
|
It should be accessible over UART2 pins (see pinout on wiki) or SSH.
|
|
- Username: `nixos`
|
|
- Password: `nixos`
|
|
|
|
# Additional Notes
|
|
|
|
## Recording from CSI camera:
|
|
- https://linux-sunxi.org/CSI#CSI_on_mainline_Linux_with_v4l2
|
|
- https://www.kernel.org/doc/html/latest/userspace-api/media/v4l/subdev-formats.html
|
|
|
|
Streaming via rtmp:
|
|
|
|
Run a RTMP server on a machine on the network (assuming at 192.168.1.200).
|
|
|
|
On pinecube
|
|
```shell
|
|
$ media-ctl --set-v4l2 '"ov5640 1-003c":0[fmt:UYVY8_2X8/640x480@1/15]'
|
|
$ ffmpeg -s 640x480 -r 15 -i /dev/video0 -vcodec flv -f flv rtmp://192.168.1.200/live/pinecube
|
|
```
|
|
|
|
On receiving machine:
|
|
```shell
|
|
$ mpv "rtmp://192.168.1.200/live/pinecube" --profile=low-latency --cache-secs=1
|
|
```
|
|
|
|
To enable audio in the stream: (see section below for further audio details)
|
|
```shell
|
|
$ media-ctl --set-v4l2 '"ov5640 1-003c":0[fmt:UYVY8_2X8/320x240@1/15]'
|
|
$ ffmpeg -s 320x240 -r 15 -i /dev/video0 -f alsa -ac 1 -ar 22050 -i hw:0,0 -acodec libmp3lame -vcodec flv -f flv rtmp://192.168.1.200/live/pinecube
|
|
```
|
|
(Ensure that Mic1 is active and unmuted using `alsamixer`)
|
|
CPU usage while encoding required me to also lower camera resolution and also the audio sampling rate.
|
|
Let me know if you find ffmpeg settings that give a good balance between quality, CPU usage, and bitrate.
|
|
|
|
## Activating IR LEDs:
|
|
```shell
|
|
$ echo 1 > /sys/class/leds/pine64\:ir\:led1/brightness
|
|
$ echo 1 > /sys/class/leds/pine64\:ir\:led2/brightness
|
|
```
|
|
|
|
## GPIO:
|
|
https://linux-sunxi.org/GPIO
|
|
```shell
|
|
$ cat /sys/kernel/debug/pinctrl/1c20800.pinctrl/pinmux-pins
|
|
```
|
|
gives information about pin numbering and what pins already claimed for other things
|
|
|
|
### Enabling/disabling IR-cut filter
|
|
```shell
|
|
# Export gpio, set direction
|
|
$ echo 45 > /sys/class/gpio/export
|
|
$ echo out > /sys/class/gpio/gpio45/direction
|
|
|
|
# 1 to enable, 0 to disable
|
|
$ echo 1 > /sys/class/gpio/gpio45/value
|
|
```
|
|
|
|
### Passive IR detection
|
|
```shell
|
|
# Export gpio, set direction
|
|
$ echo 199 > /sys/class/gpio/export
|
|
$ echo in > /sys/class/gpio/gpio199/direction
|
|
|
|
# Returns 1 for presence, 0 for none
|
|
$ cat /sys/class/gpio/gpio199/value
|
|
```
|
|
|
|
## SPI NOR
|
|
In Linux, dmesg error: `spi-nor spi0.0: unrecognized JEDEC id bytes: 0b 40 18 0b 40 18`
|
|
The published schematic says it's a `GD5F4GQ4UCYIG`, however the label on the pinecube I have is for an `XT25F128B`.
|
|
And this matches the JEDEC bytes reported in Linux.
|
|
|
|
### SPI Boot
|
|
Run `nix-build -A firmware-installer`. Then,
|
|
```shell
|
|
$ dd if=result/firmware-installer-image.img of=/dev/sdX bs=1024
|
|
```
|
|
Then, use the menu option available over UART2 to install u-boot to the SPI.
|
|
|
|
I initially flashed a bad u-boot, which caused me to be unable to boot from MMC or even FEL.
|
|
I was able to force the Pinecube to load into FEL by grounding the `SPI0_MISO` pin.
|
|
Then, I could boot into u-boot and erase the SPI, returning the Pinecube to factory condition.
|
|
|
|
## Ethernet
|
|
Working fine in linux, and now also u-boot with patch derived from: https://lists.denx.de/pipermail/u-boot/2020-May/413924.html
|
|
S3 datasheet says it supports up to 1000Mbit, but we only have a 100Mbit PHY: `H1601CG`
|
|
Maybe this is for easier PoE support?
|
|
|
|
## USB
|
|
Not working in linux or u-boot.
|
|
dmesg reports: `supply vcc not found, using dummy regulator`
|
|
|
|
## WIFI
|
|
`iwlist wlan0 scan` worked fine.
|
|
Stopped working after starting `wpa_supplicant`.
|
|
Dmesg errors:
|
|
```
|
|
Oct 19 06:11:31 nixos wpa_supplicant[926]: Successfully initialized wpa_supplicant
|
|
Oct 19 06:11:32 nixos kernel: sunxi-mmc 1c10000.mmc: data error, sending stop command
|
|
Oct 19 06:11:32 nixos kernel: sunxi-mmc 1c10000.mmc: send stop command failed
|
|
```
|
|
|
|
## Audio
|
|
S3 has significant differences when compared with V3s.
|
|
It has 4 audio inputs (3 mics, 1 line in), and 2 audio outputs (headphone and line out).
|
|
Currently, only the microphone is working. I tried to get audio output working but didn't have any luck.
|
|
Use `alsamixer` to ensure mic is active and unmuted.
|
|
```shell
|
|
$ ffmpeg -f alsa -ar 22050 -i hw:0,0 -acodec mp3 -f flv rtmp://192.168.1.200/live/pinecube
|
|
```
|
|
|
|
## Power Supply
|
|
See `/sys/class/power_supply/axp20x-ac`.
|
|
See `/sys/class/power_supply/axp20x-battery/{status,capacity}`.
|
|
Green LED if power is on.
|
|
Red LED if battery is charging.
|